FREE SHIPPING ON SELECT PRODUCTS • MADE IN USA • TECHNICAL SUPPORT WITH EVERY ORDER
New
Professional acid-chloride plating prep
Nickel Strike Solution - 1 Gallon
A professional-grade acid-chloride nickel strike solution for preparing compatible metal surfaces before the main nickel plating bath when adhesion is the priority.
One gallon professional nickel strike solution
Used before the main nickel plating bath
Supports adhesion on compatible prepared surfaces
Solution only; plating equipment and preparation products sold separately
Nickel strike solution is used as a plating-preparation step before the main nickel deposit. Its purpose is to establish an adherent initial nickel layer on a correctly cleaned and activated compatible surface. It is not a replacement for the main Watts nickel plating solution and is not intended to provide the full decorative or functional build by itself.
The need for a strike depends on the base metal, alloy, existing finish, and preparation sequence. Difficult or critical surfaces may benefit from this additional step, but an unsuitable process can still produce poor adhesion. Confirm the exact substrate with technical support before processing an unfamiliar or valuable part.
What the buyer still needs
This product is one gallon of nickel strike solution. A controlled electroplating setup generally also requires a compatible chemical-resistant tank, suitable anode arrangement, an adjustable direct-current power supply, connections, rinse stages, and substrate-specific cleaning and activation products. Follow the product instructions for the controlling equipment and operating requirements.
Do not use the strike bath to compensate for oil, polishing compound, oxide, scale, fingerprints, or inadequate rinsing. Prepare the surface completely, avoid touching it after activation, transfer promptly between steps, and run a same-material test coupon when possible. After striking, move the part into the appropriate main nickel bath according to the supplied process guidance.
Who it is for
Built for real shop work.
Plating shops, restoration businesses, repair operations, and experienced makers preparing compatible parts for a subsequent nickel deposit.
In the order
What you get.
1 gallon acid-chloride nickel strike solution
Before you order
Compatibility and setup.
Compatible metals
Confirm your exact alloy and surface with technical support before ordering.
Volume
Listed size
1 gallon solution
Coverage
Not published
Operating notes
Temperature
Follow the included product instructions for the specified operating range.
pH
Follow the included product instructions for the specified operating range.
Power / equipment
Nickel strike is an electroplating preparation process. Confirm the required adjustable DC power supply and anode setup in the included instructions.
Preparation
Remove oils, soils, polishing compound, scale, and oxide; rinse thoroughly; then use the substrate-specific activation sequence before striking.
Not sure this is the right product? Email technical support with the base metal and what you want the finish to do.
How to start
A practical sequence.
The included product instructions are the controlling procedure.
01
Confirm that a nickel strike is appropriate for the exact substrate.
02
Clean, rinse, and activate the surface using the correct substrate-specific sequence.
03
Set up the strike bath and electroplating equipment according to the product instructions.
04
Apply the strike, rinse as directed, and transfer to the main nickel plating bath.
The result
What to expect.
Designed to provide an initial nickel layer that supports adhesion before the main nickel plating process on correctly prepared compatible surfaces.
Be realistic
What still matters.
This is a preparation bath, not a complete nickel plating system or final-build bath. Substrate suitability and exact operating values must be confirmed before use.
Shipping
Getting it to you.
Shipping terms are shown during the existing Square checkout. Contact support if timing is critical.
Need it for a job with a hard date? Email support when you order.
Safety
Read before use.
Use the label, instructions, and Safety Data Sheet. Technical support is included if you get stuck.
It provides an initial nickel preparation layer before the main nickel plating bath, helping establish adhesion on a correctly prepared compatible surface.
Is this the main nickel plating bath?
No. Nickel strike is a preparation step. Use the appropriate main nickel plating solution afterward for the intended deposit build and finish.
Which metals need a nickel strike?
The need for a strike depends on the exact alloy and existing surface. Confirm your substrate and preparation sequence with technical support before use.
What equipment is required?
A controlled electroplating setup is required. Confirm the suitable tank, anode arrangement, adjustable DC power supply, connections, and preparation products in the included instructions.
Is this ready to use?
Yes. This is a one-gallon professional-grade acid-chloride nickel strike solution. Follow the supplied instructions before operating the bath.
Also useful
Complete the setup.
Nickel Electroplating Solutions • Free shipping
Nickel Watts Electroplating Solution - 1 Gallon Professional Bath
